Skip to main content

Misfeed and cleanning error for CM2320 printer


Q:  What is the problem for Misfeed and Cleanning error?
Ans:  This error is because of Misfeed. The printer detect that paper which is select for printing is moving too slow or too fast and the print is not properly printed on paper, some part of print is printed on
transfer belt thats why printer cleanning cycle run after every one or two paper.

Solution:
   Change the Tray 2 paper feed roller and sapration pad of printer.


1).Raise the printer to gain access to the roller. Use the side frame for lifting the printer. Do not raise the printer using the front door or the paper tray area.
 
2). There are two locking tabs that hold the roller in place. Use your fingers to remove or snap ring pliers. Remove the paper pick up roller.
        
3).Release the two cover locking pins and remove the separation roller cover by rotating down.
4).Release the separation roller locking pins and remove the roller.  Reinstall the roller cover on the locking pin and rotate it towards the roller until it snaps into place.



5).To remove the tray 1 pickup roller it will need to be lowered by pushing down on both ends of the assembly.
6).Release the two locking tabs and rotate the roller away from the printer.
7).Replace the separation pad for tray 1 by releasing the retaining tabs. The base that holds the pad will be loose when the pad is removed. There is a spring that can fall out.
8).To replace the automatic document feeder rollers open the ADF cover and release the spring that is attached to the end of the pick roller assembly.
9). Lift up on the pickup assembly and slide it towards the front of the printer to remove.


Remark: Many sites and blog suggest paper setting from jetadmin or hp tool box but nothing help me.

Comments

Popular posts from this blog

Toshiba bios password removal for latest models

http://www.laptoprefix.com/viewforum.php?f=25 Satellite P100 & Satellite Pro P100 Open Wi-Fi Cover Remove Mini Card Wi-Fi card Locate & Short Out JP8 for 5 Seconds Remove short and turn on NO BOOT Press & Hold Power button to turn off Turn on again & password is cleared Satellite L10, L20, L30 & Satellite Pro L20 Open Wi-Fi Cover Locate & Short Out JP1 for 15 Seconds (Satellite L10) Satellite L20/Pro L20 short out G1 Satellite M100 & Tecra A6 Open Memory Cover Remove Memory Remove Black plastic insulation Locate & Short CMOS CLR1 for 15 Seconds NOTE: All the following models use the same password removal process. Satellite: 17xx Series, 1000, 1110,1130, 1200, 1900, 2430, 3000 P20,P30, P33, A30, A70, A80, M40X, M50,M60, M70, M100 Tecra A3/S2, A5, A6 The jumper is always located under or near the memory modules Depending on the model the jumper could be labelled J1, J2, J5, J7, J9 or CMOS CLR1 (M100 & A6) S...

Dell bios password removal for latest models

RESET Dell  Bioses Reset Dell 15R-N5110 Bios   Add caption remove motherboard from you laptop. connect power and turn on. short G2201 only one time.its shout down. remove power and assemble your laptop again Then go to bios by press F2. note: This instructions for help only and for professionals only. general users do not try this.        Don't short G2201 two times or in even count.it will show you password prompt again. RESET DELL 1545 Bios 1545 mobo  with Graphics   1545 without Graphics remove motherboard from you laptop. connect power and turn on. short G49 only one time.its shout down. remove power and assemble your laptop again Then go to bios by press F2. note: This instructions for help only and for professionals only. general users do not try this.          1545 without graphics can be reset only to remove wifi co...

HP/Compaq led errors

HP/Compaq : "The following table illustrates the meaning of blink codes used on some notebooks with EFI environment. The blink or beep codes on your computer may have different meanings. When you contact HP for support, the agent needs to know the model of your computer and may ask you about blinking LEDs or beeping tones to help troubleshoot a startup problem.Meaning of Sample Blink Codes for some EFI Notebooks Number of Blinks or BeepsLocation of Blinking LEDsComponent Being CheckedError Condition Continuous glowBattery power LEDBatteryThe AC adapter is attached and the battery is charging, but does not yet have sufficient charge to power the notebook. 1time---Caps Lock/Num Lock-----CPU------------------CPU not functional 2time---Caps Lock/Num Lock-----BIOS----------------BIOS corruption failure 3time---Caps Lock/Num Lock-----Memory-------------Module error not functional 4time---Caps Lock/Num Lock-----Graphics--------------Graphics controller not functional 5time---Caps Lock/Nu...