LAPTOP REPAIR

RESET Dell  Bioses Reset Dell 15R-N5110 Bios   Add caption remove motherboard from you laptop. connect power and turn on. short G2201 only one time.its shout down. remove power and assemble your laptop again Then go to bios by press F2. note: This instructions for help only and for professionals only. general users do not try this.        Don't short G2201 two times or in even count.it will show you password prompt again. RESET DELL 1545 Bios 1545 mobo  with Graphics   1545 without Graphics remove motherboard from you laptop. connect power and turn on. short G49 only one time.its shout down. remove power and assemble your laptop again Then go to bios by press F2. note: This instructions for help only and for professionals only. general users do not try this.          1545 without graphics can be reset only to remove wifi co...

ALL LAPTOP REPAIRING SOLUTION: How to fix Dell BIOS 8 beep error. : In this post I'll  fix a Dell n5110 laptop that beeps on start-up but nothing comes on laptop display screen.  This post will also help...

Lenovo bios

Hp DV6-30xxxx Bios (01448F29) binary file : Main   KBC

Open whole laptop and dissamble the main board Locate bios chip Remove the bios chip programe with eeprom writer download latest bios from hp site of your laptop support. extract with winrar or 7zip to get .fd or bin file check bios type turn xxxxxxx.fd to xxxx.bin load it using application you are using with your eeprom writer. mount it on board and reassamble it. turn your computer on its working with boot order.

Q:  What is the problem for Misfeed and Cleanning error? Ans:  This error is because of Misfeed. The printer detect that paper which is select for printing is moving too slow or too fast and the print is not properly printed on paper, some part of print is printed on transfer belt thats why printer cleanning cycle run after every one or two paper. Solution:    Change the Tray 2 paper feed roller and sapration pad of printer. 1).Raise the printer to gain access to the roller. Use the side frame for lifting the printer. Do not raise the printer using the front door or the  paper tray  area.   2). There are two locking tabs that hold the roller in place. Use your fingers to remove or snap ring pliers. Remove the paper pick up roller.          3).Release the two cover locking pins and remove the  separation roller  cover by rotating down. 4).Release the  separation roller ...

Bios file link  ....................................................... ............................................................ ..............................

( Warning: Without Battery This Process not working ) Download Bios from lenovo website: Extract it with winrar and copy xxxx.rom file to fdd Drive or usb : 1. Put in USB Floppy Drive 2. Hold FN+R 3. plug in Power Supply (still holding FN+R) 4. Press the Power on/off Button 5. look at the USB LED its start blinking after 5-7 min its restart.

Fn+B or Win+B :      Hp/Compaq  Phoenix bios,  Toshi b a        Fn+Esc:     Acer Bios   few insyde bios    Fn+F :  This is work for l300 Toshiba Fn+R : This work for S10 Series Of Lenovo Min  Ctrl+Home: AMI BIOS MSI Boards  Hold down the END key:   Dell Bios crisys key

http://www.laptoprefix.com/viewforum.php?f=25 Satellite P100 & Satellite Pro P100 Open Wi-Fi Cover Remove Mini Card Wi-Fi card Locate & Short Out JP8 for 5 Seconds Remove short and turn on NO BOOT Press & Hold Power button to turn off Turn on again & password is cleared Satellite L10, L20, L30 & Satellite Pro L20 Open Wi-Fi Cover Locate & Short Out JP1 for 15 Seconds (Satellite L10) Satellite L20/Pro L20 short out G1 Satellite M100 & Tecra A6 Open Memory Cover Remove Memory Remove Black plastic insulation Locate & Short CMOS CLR1 for 15 Seconds NOTE: All the following models use the same password removal process. Satellite: 17xx Series, 1000, 1110,1130, 1200, 1900, 2430, 3000 P20,P30, P33, A30, A70, A80, M40X, M50,M60, M70, M100 Tecra A3/S2, A5, A6 The jumper is always located under or near the memory modules Depending on the model the jumper could be labelled J1, J2, J5, J7, J9 or CMOS CLR1 (M100 & A6) S...

(Warning). This Toshiba bios password removal process is meant for use on Toshiba laptops that you own or have had permission from the rightful owner to remove the password. If any of these processes are done incorrectly it may result in complete system failure or permanent system damage. Key Disk Some Toshiba bios passwords can be reset using the Key Disk.exe utility, to do this you need a 1.44Mb floppy disk. Format the disk using Windows and then with a hex editor, change the first five bytes of the second sector to 4B 45 59 00 00. Then put the floppy into your machine and boot it up, you’ll be asked for a password, just press Enter. Then when you’re asked to set the password, type Y then Enter, this will get you into the bios configuration where you can then type in a new password. Parallel Port To make it you will need a 25 pin DB25 plug, take the plug apart and join these pins using some old cable; Pins:  1-5-10,  2-11,  3-17,  4-...

hcl-c9504 Bios (Whiety bios,LX8 Sn-b1381,f12dc108) F12DG1 bios this link is for hcl bios in rom file.

This image is for v3000 8pin to 6pin mouse connection

Keyboard Status Lights numpad - caps lock - scrol lock (light code given in serial) The green lights located above the keyboard indicate the following: Turns on when the numeric keypad is enabled. Turns on when the Caps Lock function is enabled. Turns on when the Scroll Lock function is enabled. LED Error Codes The following table shows the possible LED codes that may display in a no-POST situation. Appearance Description Next Step ON-FLASH-FLASH No SODIMMs are installed Install supported memory modules. If memory is already present, reseat the module(s) one at time in each slot. Try known good memory from another computer or replace the memory. Replace the system board. FLASH-ON-ON System board error Reseat the processor. Replace the system board. Replace the processor. FLASH-ON-FLASH Display panel error R...

CQ60-101 au  amd bios

HCL BIOS  P5903

bios here

lenovo 3000 g430 bios file Zenith executive bios